【华为】设备集群配置案例（通过业务口）——说明
发布作者：微思网络 发布时间：2024-10-23 浏览量：0次
说明：
逻辑集群端口配置完成后，建议执行display css css-port saved命令查看配置的端口是否正确以及状态是否都为Up。
使能集群功能
# 使能SwitchA的集群功能并重新启动SwitchA。
[SwitchA] css enable
Warning: The CSS configuration will take effect only after the system is rebooted. The next CSS mode is LPU. Reboot now? [Y/N]:y
# 使能SwitchB的集群功能并重新启动SwitchB。
[SwitchB] css enable
Warning: The CSS configuration will take effect only after the system is rebooted. The next CSS mode is LPU. Reboot now? [Y/N]:y
检查集群组建
# 查看指示灯状态。
SwitchA主控板上ACT灯绿色常亮，表示该主控板为集群系统主用主控板，SwitchA为主交换机。
SwitchB主控板上ACT灯绿色闪烁，表示该主控板为集群系统备用主控板，SwitchB为备交换机。
# 通过任意主控板上的Console口本地登录集群，使用命令行查看集群组建是否成功。
<SwitchA> display device
Chassis 1 (Master Switch)
S9706's Device status:
Slot Sub Type Online Power Register Status Role
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1 - EH1D2X12SSA0 Present PowerOn Registered Normal NA
2 - EH1D2X12SSA0 Present PowerOn Registered Normal NA
3 - EH1D2X12SSA0 Present PowerOn Registered Normal NA
4 - EH1D2G48SEC0 Present PowerOn Registered Normal NA
7 - EH1D2SRUC000 Present PowerOn Registered Normal Master
8 - EH1D2SRUC000 Present PowerOn Registered Normal Slave
PWR1 - - Present PowerOn Registered Normal NA
PWR2 - - Present - Unregistered - NA
CMU2 - EH1D200CMU00 Present PowerOn Registered Normal Master
FAN1 - - Present PowerOn Registered Abnormal NA
FAN2 - - Present - Unregistered - NA
Chassis 2 (Standby Switch)
S9706's Device status:
Slot Sub Type Online Power Register Status Role
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1 - EH1D2X12SSA0 Present PowerOn Registered Normal NA
2 - EH1D2X12SSA0 Present PowerOn Registered Normal NA
3 - EH1D2X12SSA0 Present PowerOn Registered Normal NA
4 - EH1D2G48SEC0 Present PowerOn Registered Normal NA
7 - EH1D2SRUC000 Present PowerOn Registered Normal Master
8 - EH1D2SRUC000 Present PowerOn Registered Normal Slave
PWR1 - - Present PowerOn Registered Normal NA
PWR2 - - Present PowerOn Registered Normal NA
CMU1 - EH1D200CMU00 Present PowerOn Registered Normal Master
FAN1 - - Present PowerOn Registered Normal NA
FAN2 - - Present PowerOn Registered Normal NA
以上显示信息中，能够查看到两台成员交换机的单板状态，表示集群建立完成。
# 查看集群链路拓扑是否与硬件连接一致。
<SwitchA> display css channel all
CSS link-down-delay: 500ms
Chassis 1 || Chassis 2
================================================================================
Num [CSS port] [LPU Port] || [LPU Port] [CSS port]
1 1/1 XGigabitEthernet1/1/0/1 XGigabitEthernet2/1/0/1 2/1
2 1/1 XGigabitEthernet1/1/0/2 XGigabitEthernet2/1/0/2 2/1
3 1/2 XGigabitEthernet1/2/0/1 XGigabitEthernet2/2/0/1 2/2
4 1/2 XGigabitEthernet1/2/0/2 XGigabitEthernet2/2/0/2 2/2
Chassis 2 || Chassis 1
================================================================================
Num [CSS port] [LPU Port] || [LPU Port] [CSS port]
1 2/1 XGigabitEthernet2/1/0/1 XGigabitEthernet1/1/0/1 1/1
2 2/1 XGigabitEthernet2/1/0/2 XGigabitEthernet1/1/0/2 1/1
3 2/2 XGigabitEthernet2/2/0/1 XGigabitEthernet1/2/0/1 1/2
4 2/2 XGigabitEthernet2/2/0/2 XGigabitEthernet1/2/0/2 1/2
以上显示信息中，可以看出集群链路拓扑与硬件连接一致，表示业务口集群建立成功。
配置集群系统与上、下游设备的Eth-Trunk
# 在集群系统上行端口创建Eth-Trunk，并加入Eth-Trunk成员接口。
<SwitchA> system-view
[SwitchA] sysname CSS //给集群系统重新命名
[CSS] interface eth-trunk 10
[CSS-Eth-Trunk10] quit
[CSS] interface xgigabitethernet 1/3/0/4
[CSS-XGigabitEthernet1/3/0/4] eth-trunk 10
[CSS-XGigabitEthernet1/3/0/4] quit
[CSS] interface xgigabitethernet 2/3/0/4
[CSS-XGigabitEthernet2/3/0/4] eth-trunk 10
[CSS-XGigabitEthernet2/3/0/4] quit
# 在集群系统下行端口上创建与SwitchC之间的Eth-Trunk，并加入Eth-Trunk成员接口。
[CSS] interface eth-trunk 20
[CSS-Eth-Trunk20] quit
[CSS] interface gigabitethernet 1/4/0/3
[CSS-GigabitEthernet1/4/0/3] eth-trunk 20
[CSS-GigabitEthernet1/4/0/3] quit
[CSS] interface gigabitethernet 2/4/0/5
[CSS-GigabitEthernet2/4/0/5] eth-trunk 20
[CSS-GigabitEthernet2/4/0/5] quit
# 在集群系统下行端口上创建与SwitchD之间的Eth-Trunk，并加入Eth-Trunk成员接口。
[CSS] interface eth-trunk 30
[CSS-Eth-Trunk30] quit
[CSS] interface gigabitethernet 1/4/0/5
[CSS-GigabitEthernet1/4/0/5] eth-trunk 30
[CSS-GigabitEthernet1/4/0/5] quit
[CSS] interface gigabitethernet 2/4/0/3
[CSS-GigabitEthernet2/4/0/3] eth-trunk 30
[CSS-GigabitEthernet2/4/0/3] return
# 在SwitchE上创建Eth-Trunk，并加入Eth-Trunk成员接口。
<HUAWEI> system-view
[HUAWEI] sysname SwitchE
[SwitchE] interface eth-trunk 10
[SwitchE-Eth-Trunk10] quit
[SwitchE] interface xgigabitethernet 1/0/1
[SwitchE-XGigabitEthernet1/0/1] eth-trunk 10
[SwitchE-XGigabitEthernet1/0/1] quit
[SwitchE] interface xgigabitethernet 1/0/2
[SwitchE-XGigabitEthernet1/0/2] eth-trunk 10
[SwitchE-XGigabitEthernet1/0/2] quit
# 在SwitchC上创建Eth-Trunk，并加入Eth-Trunk成员接口。
<HUAWEI> system-view
[HUAWEI] sysname SwitchC
[SwitchC] interface eth-trunk 20
[SwitchC-Eth-Trunk20] quit
[SwitchC] interface gigabitethernet 1/0/1
[SwitchC-GigabitEthernet1/0/1] eth-trunk 20
[SwitchC-GigabitEthernet1/0/1] quit
[SwitchC] interface gigabitethernet 1/0/2
[SwitchC-GigabitEthernet1/0/2] eth-trunk 20
[SwitchC-GigabitEthernet1/0/2] quit
# 在SwitchD上创建Eth-Trunk，并加入Eth-Trunk成员接口。
<HUAWEI> system-view
[HUAWEI] sysname SwitchD
[SwitchD] interface eth-trunk 30
[SwitchD-Eth-Trunk30] quit
[SwitchD] interface gigabitethernet 1/0/1
[SwitchD-GigabitEthernet1/0/1] eth-trunk 30
[SwitchD-GigabitEthernet1/0/1] quit
[SwitchD] interface gigabitethernet 1/0/2
[SwitchD-GigabitEthernet1/0/2] eth-trunk 30
[SwitchD-GigabitEthernet1/0/2] quit
# 检查配置结果。
上述配置成功后，在任意视图下执行命令display trunkmembership eth-trunk，可以看到Eth-Trunk接口的成员口信息。
以集群系统上Eth-Trunk 10的显示为例。
<CSS> display trunkmembership eth-trunk 10
Trunk ID: 10
Used status: VALID
TYPE: ethernet
Working Mode : Normal
Number Of Ports in Trunk = 2
Number Of Up Ports in Trunk = 2
Operate status: up
Interface XGigabitEthernet1/3/0/4, valid, operate up, weight=1
Interface XGigabitEthernet2/3/0/4, valid, operate up, weight=1
配置多主检测功能（此处选择代理方式进行配置，将SwitchC作为代理设备。命令行格式以V200R003C00及之后的版本为例）
# 在集群系统上配置Eth-Trunk接口的代理方式多主检测功能。
<CSS> system-view
[CSS] interface eth-trunk 20
[CSS-Eth-Trunk20] mad detect mode relay //V200R002C00版本命令行格式为dual-active detect mode relay
[CSS-Eth-Trunk20] quit
[CSS] quit
# 配置代理设备SwitchC的代理功能。
[SwitchC] interface eth-trunk 20
[SwitchC-Eth-Trunk20] mad relay //V200R002C00版本命令行格式为dual-active relay
[SwitchC-Eth-Trunk20] quit
[SwitchC] quit
# 检查配置结果。
在集群系统上查看集群多主检测的配置信息。
<CSS> display mad //V200R002C00版本命令行格式为display dual-active
Current MAD domain: 0
MAD direct detection enabled: NO
MAD relay detection enabled: YES
在SwitchC上查看配置的代理信息。
<SwitchC> display mad proxy //V200R002C00版本命令行格式为display dual-active proxy
Mad relay interfaces configured:
Eth-Trunk20
配置文件
集群系统的配置文件
#
sysname CSS
#
interface Eth-Trunk10
#
interface Eth-Trunk20
mad detect mode relay
#
interface Eth-Trunk30
#
interface GigabitEthernet1/4/0/3
eth-trunk 20
#
interface XGigabitEthernet1/3/0/4
eth-trunk 10
#
interface GigabitEthernet1/4/0/5
eth-trunk 30
#
interface GigabitEthernet2/4/0/3
eth-trunk 30
#
interface XGigabitEthernet2/3/0/4
eth-trunk 10
#
interface GigabitEthernet2/4/0/5
eth-trunk 20
#
return
SwitchC的配置文件
#
sysname SwitchC
#
interface Eth-Trunk20
mad relay
#
interface GigabitEthernet1/0/1
eth-trunk 20
#
interface GigabitEthernet1/0/2
eth-trunk 20
#
return
SwitchD的配置文件
#
sysname SwitchD
#
interface Eth-Trunk30
#
interface GigabitEthernet1/0/1
eth-trunk 30
#
interface GigabitEthernet1/0/2
eth-trunk 30
#
return
SwitchE的配置文件
# return
sysname SwitchE
#
interface Eth-Trunk10
#
interface XGigabitEthernet1/0/1
eth-trunk 10
#
interface XGigabitEthernet1/0/2
eth-trunk 10
#
